The short version of mobile phase fits in a sentence. The long version — which is the one that helps — is below.
This page was last updated on 2026-01-31 and is reviewed periodically as new material appears.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Most common for neutral and moderately polar analytes |
| Column particle size | 3–5 µm | Smaller particles improve resolution but raise backpressure |
| Mobile phase pH range | 2–8 | Silica-based columns may degrade outside this range |
| Typical flow rate | 1.0–2.0 mL/min | For analytical columns with 4.6 mm internal diameter |
| Common synonyms | HPLC, LC, high-pressure liquid chromatography | High-performance liquid chromatography is the standard expansion |
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Anoop's father, who was the Minister for Food and Civil Supplies, died on 30 October 2011. Following this, Anoop was nominated by the Kerala Congress (Jacob) and UDF to contest from the Piravom assembly seat previously represented by his father. His father had lost the sitting seat in 2006 elections and recaptured it in 2011 election by a margin of 157 votes. Against Anoop Jacob, CPI(M)–led LDF once again fielded M. J. Jacob, who had won against T. M. Jacob in 2006 and lost in 2011. Since the result of Piravom by-election mattered heavily to the ruling UDF who had a slender margin of 1 seat in the Legislative assembly over LDF, the constituency witnessed intense campaigning from both sides. Election was held on 17 March 2012 and results were announced on 21 March 2012. Anoop Jacob won the by-election by a significant margin of 12,071 votes. He was sworn in as an MLA on 22 March 2012. Anoop took oath as the Minister for Food & Civil Supplies on 12 April 2012 and occupied office in the North Block of the Kerala Secretariat; both portfolio & office last held by his departed father.
Pickston founded Skinny Revolution to help people to lose weight after she gained 7 stone in 14 months, partly whilst pregnant, using a Wegovy (semaglutide) injection, which is a 2.4 mg injectable prescription medicine used as an appetite suppressant. Pickston is engaged to former West Ham United co-chairman David Sullivan. She has a son, Jake, with her former husband Mark Pickston. She lives in Hale Barns, in the house which was filmed for the Real Housewives of Cheshire episodes that she appeared in.
Banting lived at the house in London for ten months, beginning in June, 1920. He attempted a private medical practice and when it was unsuccessful, he began working at the University of Western Ontario; his research for a lecture there was what inspired his 25 word idea that provided the key to discovering insulin, and prevented the certain death of those affected by diabetes. Banting returned to the University of Toronto to begin his research on insulin in the spring of 1921. Banting House is dedicated to the story behind the discovery of insulin, as well as Banting's life and career. Its galleries focus on everything from his time spent in London, to his contributions in both World Wars, to his efforts as an artist. Some notable artifacts include Banting's original art, desk, medicine cabinet, and bed frame, as well as his Military Cross, the KBE, and his official replica of the Nobel Prize. Banting House was designated a National Historic Site of Canada in 1997.
Across several benchmarks, AlphaFold3 has demonstrated, on average, superior performance to conventional search-based docking algorithms in predicting small-molecule–protein binding modes. AlphaFold 3 version can predict structures of protein complexes with a very limited set of selected cofactors and co- and post-translational modifications. Between 50% and 70% of the structures of the human proteome are incomplete without covalently-attached glycans. Studies have shown that although AlphaFold3 can jointly model protein–ligand co-folding, its accuracy drops markedly on test cases with low similarity to its training data—an area of particular importance for drug discovery. Other work has found that AlphaFold is insensitive to adversarial decoys generated by altering the physicochemical properties of binding pockets, suggesting potential reliance on training-set memorization rather than genuine chemical awareness.
ADAMTS7 was identified as a protease that binds and cleaves COMP in a yeast two-hybrid screen using the epidermal growth factor (EGF) domain of COMP as the bait. However, this initial finding has been contested; a 2025 study demonstrated that purified ADAMTS7 does not exhibit proteolytic cleavage activity toward purified COMP. Furthermore, three independent unbiased N-terminal amine isotopic labeling of substrates (N-TAILS) proteomic studies identified a number of candidate substrates for ADAMTS7 but did not identify COMP as a potential substrate. Consequently, there is as yet no scientific consensus on the physiological function of ADAMTS7. Tissue inhibitor of metalloproteinases 4 (TIMP-4) appears to be the physiological inhibitor of ADAMTS7.
Sources: en.wikipedia.org
Alpha-synuclein has been shown to interact with Dopamine transporter, Parkin (ligase), Phospholipase D1, SNCAIP, Tau protein. Beta amyloid Synuclein Contursi Terme - the village in Italy where a mutation in the α-synuclein gene led to a family history of Parkinson's disease Anti-α-synuclein drug Media related to Alpha-synuclein at Wikimedia Commons alpha-Synuclein at the U.S. National Library of Medicine Medical Subject Headings (MeSH) Human SNCA genome location and SNCA gene details page in the UCSC Genome Browser.
Another strategy for site-specific amine conjugation to proteins is to replace lysine residues with arginine residues (LDVs). If all lysines are depleted then the only remaining free amine is at the amino terminus (N-terminus) of the protein. In the case where the protein is an antibody Fc domain, a recombinant LDV Fc can still be purified using protein A. LDV Fc proteins fused with short peptide targeting sequences can be used to deliver conjugated payloads, including nanoparticles, to specific cell surface proteins. The majority of ADCs under development or in clinical trials are for oncological and hematological indications. This is primarily driven by the inventory of monoclonal antibodies, which target various types of cancer. However, some developers are looking to expand the application to other important disease areas.
Human serum albumin is the main protein of human blood plasma. It makes up around 50% of human plasma proteins. It binds water, cations (such as Ca2+, Na+ and K+), fatty acids, hormones, bilirubin, thyroxine (T4) and pharmaceuticals (including barbiturates). Its main function is to regulate the oncotic pressure of blood. The isoelectric point of albumin is 4.7. Alpha-fetoprotein is a fetal plasma protein that binds various cations, fatty acids and bilirubin. Vitamin D-binding protein binds to vitamin D and its metabolites, as well as to fatty acids. Afamin binds vitamin E. It seems to carry lipidated Wnt proteins and Vitamin E around. Extracellular matrix protein 1 is a less canonical albumin. It regulates bone mineralization. The four canonical human albumins are arranged on chromosome 4 region 4q13.3 in a tandem manner.
Asparagine peptide lyase are one of the seven groups in which proteases, also termed proteolytic enzymes, peptidases, or proteinases, are classified according to their catalytic residue. The catalytic mechanism of the asparagine peptide lyases involves an asparagine residue acting as nucleophile to perform a nucleophilic elimination reaction, rather than hydrolysis, to catalyse the breaking of a peptide bond. The existence of this seventh catalytic type of proteases, in which the peptide bond cleavage occurs by self-processing instead of hydrolysis, was demonstrated with the discovery of the crystal structure of the self-cleaving precursor of the Tsh autotransporter from E. coli. These enzymes are synthesized as precursors or propeptides, which cleave themselves by an autoproteolytic reaction. The self-cleaving nature of asparagine peptide lyases contradicts the general definition of an enzyme given that the enzymatic activity destroys the enzyme. However, the self-processing is the action of a proteolytic enzyme, notwithstanding the enzyme is not recoverable from the reaction.
In addition to regulating the experiments that were conducted, the guidelines also forbade the performance of other experiments. One such experiment was the cloning of recombinant DNAs derived from highly pathogenic organisms. In addition, neither the cloning of DNA containing toxin genes nor large-scale experiments using recombinant DNAs that were able to make products that were potentially harmful to humans, animals, or plants were allowed under the guidelines. These experiments were banned because the potential biohazards could not be contained by the then-current safety precautions.
Sources: en.wikipedia.org
The topology of a β-sheet describes the order of hydrogen-bonded β-strands along the backbone. For example, the flavodoxin fold has a five-stranded, parallel β-sheet with topology 21345; thus, the edge strands are β-strand 2 and β-strand 5 along the backbone. Spelled out explicitly, β-strand 2 is H-bonded to β-strand 1, which is H-bonded to β-strand 3, which is H-bonded to β-strand 4, which is H-bonded to β-strand 5, the other edge strand. In the same system, the Greek key motif described above has a 4123 topology. The secondary structure of a β-sheet can be described roughly by giving the number of strands, their topology, and whether their hydrogen bonds are parallel or antiparallel. β-sheets can be open, meaning that they have two edge strands (as in the flavodoxin fold or the immunoglobulin fold) or they can be closed β-barrels (such as the TIM barrel). β-Barrels are often described by their stagger or shear. Some open β-sheets are very curved and fold over on themselves (as in the SH3 domain) or form horseshoe shapes (as in the ribonuclease inhibitor). Open β-sheets can assemble face-to-face (such as the β-propeller domain or immunoglobulin fold) or edge-to-edge, forming one big β-sheet.
The formylglycine tag or aldehyde tag is a convenient 6- or 13-amino acids long tag fused to a protein of interest. The 6-mer tag represents the small core consensus sequence and the 13-mer tag the longer full motif. The experiments on the genetically encoded aldehyde tag by clearly showed the high conversion efficiency with only the core consensus sequence present. Four proteins were produced recombinantly in E.coli with an 86% efficiency of for the full-length motif and >90% efficiency for the 6-mer determined by mass spectrometry. The size of the sequence is analogous to the commonly used 6x His-Tag and has the advantage that it can also be genetically encoded. The sequence is recognized in the ER solely depending on primary sequence and subsequently targeted by FGE. Notably, in the setup of recombinant expression proteins in E. coli a coexpression of exogenous FGE aids full conversion, although E. coli has endogenous FGE-activity. The introduction of an aldehyde tag has a workflow that consists of three segments: A the expression of the fusion protein, that carries the peptide tag derived from the sulfatase motif, B the enzymatic conversion of Cys to f(Gly) and C the bioorthogonal probing with hydrazides or alkoxy amines (Fig. 1).
There are many applications for AMS throughout a variety of disciplines. AMS is most often employed to determine the concentration of 14C, e.g. by archaeologists for radiocarbon dating. Compared to other radiocarbon dating methods, AMS requires smaller sample sizes (about 50 mg), while yielding extensive chronologies. MS technology has expanded the scope of radiocarbon dating. Samples ranging from 50,000 years old to 100 years old can be successfully dated using AMS, as other forms of mass spectrometry provide insufficient suppression of molecular isobars to resolve 13CH and 12CH2 from 14C atoms. Because of the long half-life of 14C, decay counting requires significantly larger samples. 10Be, 26Al, and 36Cl are used for surface exposure dating in geology. 3H, 14C, 36Cl, and 129I are used as hydrological tracers. Accelerator mass spectrometry is widely used in biomedical research. In particular, 41Ca has been used to measure bone resorption in postmenopausal women. List of accelerator mass spectrometry facilities Arizona Accelerator Mass Spectrometry Laboratory
CHO cells are the most common mammalian cell line used for mass production of therapeutic proteins such as monoclonal antibodies, used in 70% of therapeutic mAbs. They can produce recombinant protein on the scale of 3–10 grams per liter of culture. Products of CHO cells are suitable for human applications, as these mammalian cells perform human-like post-translational modifications to recombinant proteins, which is key to the functioning of several proteins. It is believed that CHO-K1 transgenic cells are characterized by higher monoclonal antibody expression at the expense of biomass accumulation, for example, based on CHO-K1, monoclonal antibody‑producing cell lines with productivity up to 6.5 grams per liter have been selected. Cell culture Drug development Preclinical development
AlphaKnot complements KnotProt, a database focused on experimentally determined protein structures and their topological features. KnotProt provides detailed descriptions of knots, slipknots, and related entanglements in experimentally characterized proteins, whereas AlphaKnot was developed primarily to examine the much larger population of structures generated by modern protein-structure prediction methods. AlphaKnot has been used to investigate the frequency and distribution of knots in protein families and to identify previously uncharacterized topological architectures. Large-scale analyses of AlphaFold structures have identified unusual knot types and proteins containing multiple knots, while comparison with experimentally determined structures has provided examples in which unusual predicted topologies were subsequently confirmed experimentally. The database can therefore be used both as a source of candidate knotted proteins for experimental investigation and as a computational tool for examining the relationship between protein sequence, structure, and topology.
Sources: en.wikipedia.org
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.
The pump maintains a steady flow rate and pressure, which keeps retention times reproducible. Pulsation or flow errors can shift peaks and distort quantitation. Modern pumps use feedback control to reduce these variations.
HPLC alone usually separates compounds but does not always identify them. Retention time matching with a known standard provides tentative identification. Coupling HPLC to mass spectrometry adds mass information that supports structural identification.
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.